Shaped much like a classic school ruler, this relatively narrow rule is lightweight and easy to h...
Shaped much like a classic school ruler, this relatively narrow rule is lightweight and easy to handle, making it an ideal choice for precise drawing and design tasks.
The fine laser-etched markings stand out clearly against the matte black anodized finish, with one edge that reads right to left and the other left to right. All scales are graduated in millimetre increments.
Cut from a solid aluminum extrusion, this 150mm rule is 1" wide. To avoid parallax errors, the edges are t..
For our 175mm Carpenter Square we use a piece of 6mm Aluminium Tooling plate to ensure the machin...
For our 175mm Carpenter Square we use a piece of 6mm Aluminium Tooling plate to ensure the machined part is accurate within 5 microns and ensuring the angles are accurate within +-0.05 degrees which is confirmed with our in-house CMM Machine.Our side cheeks are also machined from solid plate aluminium to ensure the same accuracy is achieved. Carpenter Square featuresAll our parts are then anodised Benchdogs Black and laser engraved with ultimate accuracy with our Trotec Lase..
These are the frogs used in our custom bench planes.
Different cutting angles are suitable fo...
These are the frogs used in our custom bench planes.
Different cutting angles are suitable for different grain; low angles cut end grain cleanly while higher angles are used to plane face grain. The higher the blade angle, the harder the plane is to push, but the less likely it is to cause tear-out in difficult grain. Available in 2" and 2 3/8" widths.
We recommend three angles based on common work requirements.
The 40° frog provides a low cutting angle that reduces ..
These are the frogs used in our custom bench planes.
Different cutting angles are suitable fo...
These are the frogs used in our custom bench planes.
Different cutting angles are suitable for different grain; low angles cut end grain cleanly while higher angles are used to plane face grain. The higher the blade angle, the harder the plane is to push, but the less likely it is to cause tear-out in difficult grain. Available in 2" and 2 3/8" widths.
We recommend three angles based on common work requirements.
The 40° frog provides a low cutting angle that reduces ..
These are the frogs used in our custom bench planes.
Different cutting angles are suitable for di...
These are the frogs used in our custom bench planes. Different cutting angles are suitable for different grain; low angles cut end grain cleanly while higher angles are used to plane face grain. The higher the blade angle, the harder the plane is to push, but the less likely it is to cause tear-out in difficult grain. Available in 2" and 2 3/8" widths.We recommend three angles based on common work requirements.The 40° frog provides a low cutting angle that reduces cut resistance and cleanly..
These are the frogs used in our custom bench planes.
Different cutting angles are suitable fo...
These are the frogs used in our custom bench planes.
Different cutting angles are suitable for different grain; low angles cut end grain cleanly while higher angles are used to plane face grain. The higher the blade angle, the harder the plane is to push, but the less likely it is to cause tear-out in difficult grain. Available in 2" and 2 3/8" widths.
We recommend three angles based on common work requirements.
The 40° frog provides a low cutting angle that reduces ..
These are the frogs used in our custom bench planes.
Different cutting angles are suitable fo...
These are the frogs used in our custom bench planes.
Different cutting angles are suitable for different grain; low angles cut end grain cleanly while higher angles are used to plane face grain. The higher the blade angle, the harder the plane is to push, but the less likely it is to cause tear-out in difficult grain. Available in 2" and 2 3/8" widths.
We recommend three angles based on common work requirements.
The 40° frog provides a low cutting angle that reduces ..
These are the frogs used in our custom bench planes.
Different cutting angles are suitable fo...
These are the frogs used in our custom bench planes.
Different cutting angles are suitable for different grain; low angles cut end grain cleanly while higher angles are used to plane face grain. The higher the blade angle, the harder the plane is to push, but the less likely it is to cause tear-out in difficult grain. Available in 2" and 2 3/8" widths.
We recommend three angles based on common work requirements.
The 40° frog provides a low cutting angle that reduces ..
Mount turning blanks with ease by attaching ring to your blank then mount to your 4-jaw chuck. Th...
Mount turning blanks with ease by attaching ring to your blank then mount to your 4-jaw chuck. There is no need to remove chuck from lathe, quickly swap between workpieces. Dovetailed clamping diameter for strong and secure holding power for larger projects. Nickel-plated cold-rolled steel for superior quality and built to last. Each faceplate ring includes a set of wood screws. 3" Faceplate Ring fits jaws with clamping diameter of 2-1/16" with minimum closed diameter of 1-7/..
Shaped much like a classic school ruler, this relatively narrow rule is lightweight and easy to h...
Shaped much like a classic school ruler, this relatively narrow rule is lightweight and easy to handle, making it an ideal choice for precise drawing and design tasks.
The fine laser-etched markings stand out clearly against the matte black anodized finish, with one edge that reads right to left and the other left to right. All scales are graduated in millimetre increments.
Cut from a solid aluminum extrusion, this 300mm rule is 1" wide. To avoid parallax errors, the edges are t..
The updated 346-hole jig has had a rethink to add more holes in additional spaces. Now we have a...
The updated 346-hole jig has had a rethink to add more holes in additional spaces. Now we have added the 80mm and 96mm. We have also added alignment pin threaded holes to allow the jig to be rested against the edge of the sheet material to start the holes from the edge of a board without starting with the jig in an already placed hole. These holes will allow for the making of an MFT table from scratch. The pin holes are set back in 16mm increments.
With our new MK2 346 (32mm,..
Protect your top with our mini protectors allowing you to create a gap between your workpiece and...
Protect your top with our mini protectors allowing you to create a gap between your workpiece and benchtop, stopping you from cutting into your top. Just set your blade to the desired height and place the protectors on each side of the cut creating support for both pieces. These small protectors not only protect the face side of your workpiece from damage and scratch marks but they can also be used as low-profile bench dogs.Supplied with 3mm silicone pads to fit on top of the..
Mount turning blanks with ease by attaching ring to your blank then mount to your 4-jaw chuck. Th...
Mount turning blanks with ease by attaching ring to your blank then mount to your 4-jaw chuck. There is no need to remove chuck from lathe, quickly swap between workpieces. Dovetailed clamping diameter for strong and secure holding power for larger projects. Nickel-plated cold-rolled steel for superior quality and built to last. Each faceplate ring includes a set of wood screws.
4-1/2" Faceplate Ring fits jaws with clamping diameter of 2-1/16" with minimum closed diameter ..
Shaped much like a classic school ruler, this relatively narrow rule is lightweight and easy to h...
Shaped much like a classic school ruler, this relatively narrow rule is lightweight and easy to handle, making it an ideal choice for precise drawing and design tasks.
The fine laser-etched markings stand out clearly against the matte black anodized finish, with one edge that reads right to left and the other left to right. All scales are graduated in millimetre increments.
Cut from a solid aluminum extrusion, this 450mm rule is 1 1/4" wide. To avoid parallax errors, the edges a..
Mount turning blanks with ease by attaching ring to your blank then mount to your 4-jaw chuck. Th...
Mount turning blanks with ease by attaching ring to your blank then mount to your 4-jaw chuck. There is no need to remove chuck from lathe, quickly swap between workpieces. Dovetailed clamping diameter for strong and secure holding power for larger projects. Nickel-plated cold-rolled steel for superior quality and built to last. Each faceplate ring includes a set of wood screws. 6" Faceplate Ring fits jaws with clamping diameter of 4-1/4" with minimum closed diameter of ..