The Crucible holdfast. Made from ductile iron in a Cincinnati family foundry that’s been in business since 1854. Based on a French design salvaged from a barn. The last holdfast you’ll likely need.

Since Roman times, the iron holdfast has been an essential piece of workbench equipment for carpenters, joiners and cabinetmakers. Yet many of us struggle with holdfasts that work inconsistently or (in thick workbench tops) not at all.

This holdfast works consistently in benches from 2" to 8" thick for three reasons: a tight fit between the shaft and hole, a rough surface finish and the fact that its shaft isn't tapered. And because of these qualities, it also will clamp objects as much as 8" off the benchtop.

For the last 10 years we’ve studied holdfasts of various shapes and sizes and put them to use in workbench tops both thick and thin. We’ve made our own designs using wrought iron salvaged from beaches. We’ve commissioned blacksmiths to make traditional designs from 18th-century pattern books. And we’ve destroyed many modern holdfasts made from grey iron through normal everyday use.

After all this experimentation, the only holdfast that never failed us was a rusted and pitted French example that a friend salvaged from a barn. When it showed up, it did not look promising. But it immediately showed its true character, cinching down every time it was struck, even in benchtops 6" or 8" thick.

We took the best qualities of this French holdfast – especially its 1" untapered and rough shaft – to design our own version. Unlike blacksmith-made holdfasts, ours is made from ductile iron instead of scarce wrought iron. 

Ductile iron is virtually unbreakable and has enough spring in it to clamp tightly and release crisply. (If you have questions about ductile, read this.)

We ship our holdfast in its rough-cast state with no surface protection against rust or tarnish. In our experience, rust adds to the grip of the holdfast and has zero disadvantages. We recommend you allow your holdfast to tarnish and age. Never oil it. And never let oil get into the holdfast holes on your bench. Because each holdfast is individually made, ground by hand and textured to improve its grip, there is significant variation from tool to tool. Some variants include small casting voids and other artifacts of the casting process. These are not defects. 

The Crucible holdfast weighs 5 pounds. The shaft is 17” long. The beak extends 6-5/8” from the shaft. It is designed to work in a 1”-diameter holdfast hole that has been reamed to match your particular holdfast or holdfasts. Each holdfast includes instructions on how to precisely fit your holdfast to your workbench. Before ordering, we recommend you download and read the instruction sheet to make sure this holdfast is ideal for you and your workbench.

Made in the United States.

Write a review

Note: HTML is not translated!
    Bad           Good
Captcha

Crucible iron Holdfast

  • 1,729.18kr (SEK)

  • Ex Tax: 1,383.35kr (SEK)

Related Products

Lie-Nielsen Holdfast
Model: 1-Holdfast

Lie-Nielsen Holdfast

Lie-Nielsen Holdfast Inspired by the work of master blacksmith, Peter Ross. Cast Duc..

638.02kr (SEK) Ex Tax: 510.42kr (SEK)

Set of woodturning chisels HSS LINE PROFI
Model: 859410

Set of woodturning chisels HSS LINE PROFI

The set contains:DescriptionTypeParting chisel HSS8182 03Round nose scraper HSS8182 04Skew hand tool..

2,327.65kr (SEK) Ex Tax: 1,862.12kr (SEK)

Set of woodturning chisels HSS LINE PROFI MINI
Model: 859400

Set of woodturning chisels HSS LINE PROFI MINI

The set contains:DescriptionTypeParting tool mini HSS8183 03Round nose scraper mini HSS8183 04Skew h..

1,132.10kr (SEK) Ex Tax: 905.68kr (SEK)

BLACKLINE MIDI ROUND SHAFT RaZoR
Model: MIDI SHAFT ROUND DIAMOND

BLACKLINE MIDI ROUND SHAFT RaZoR

335mm långt290mm kan sticka utanför handtaget12mm skaft-diameter..

965.42kr (SEK) Ex Tax: 772.34kr (SEK)

Tags: Crucible iron Holdfast, CT-HOLD, Workbench Accessories